Search | Engineering

订阅投稿

首页工程期刊工程焦点工程成就工程前沿关于我们 English

资源类型

期刊论文 4

年份

2023 1

2016 1

2014 1

2012 1

关键词

检索范围：

排序：展示方式：

Fundamental influences of particles on stirred and unstirred venting processes of foaming systems

Henrik LEIMEISTER,Jörg STEINBACH

《化学科学与工程前沿（英文）》 2014年第8卷第2期页码 141-148 doi: 10.1007/s11705-014-1423-0

摘要： Venting is the common safety measure to protect plant equipment against excessive overpressure. So far, scenarios in which particles were part of the system and should have been accounted for did ignore their presence; the scenarios were treated like a two-phase system. Current research shows that particles can have a major influence on the venting behaviour. Experimental results indicate that particles affect level swell and relief flow especially of foamy systems. Based on those results four different layers of influence of the particle have been identified and are presented in a first model. Based on this model recommendations for the development of new and more complex models are given.

关键词： venting multi-phase

HTML PDF 收藏

Properties and effect of forming sewage sludge into lightweight ceramics

Min YUE, Qinyan YUE, Yuanfeng QI, Baoyu GAO, Hui YU

《环境科学与工程前沿（英文）》 2012年第6卷第1期页码 117-124 doi: 10.1007/s11783-010-0220-3

摘要： In this work we investigated the chemical, thermal and toxic properties of dried sewage sludge (DSS), the preparation and properties of lightweight sludge ceramic (LSC) and the mechanisms of action of the organic and inorganic foaming agents (OFAs and IFAs). The chemical components and thermal properties of the raw materials were studied by Energy Dispersive X-ray Detection (EDX) and Thermogravimetric Analysis and Differential Scanning Calorimetry (DSC/TGA). The mineral phases of the raw materials and the formed ceramics were determined by X-ray Diffraction (XRD). The leaching characteristics of heavy metals were investigated with Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). Different ratios of DSS and clay were mixed and pressed into raw pellets. After drying and preheating treatment, the raw pellets were sintered at 1150°C for 10 min. The physical properties of LSC (50 wt% DSS added) were tested. The results showed that when the addition of DSS was above 50 wt%, LSC began to shrink, and a maximum density occurred. The environmental safety of LSC was satisfactory. XRD showed that some new mineral phases formed in the LSC. Observation of the microstructure by Scanning Electron Microscope (SEM) indicated that the body of LSC was porous.

关键词： sludge foaming agents ceramics preheating process

HTML PDF 收藏

Effect of polyethylene glycol on the crystallization, rheology and foamability of poly(lactic acid) containing generated polyamide 6 nanofibrils

《化学科学与工程前沿（英文）》 2023年第17卷第12期页码 2074-2087 doi: 10.1007/s11705-023-2342-8

摘要： In this study, the rheological properties, crystallization and foaming behavior of poly(lactic acid) with polyamide 6 nanofibrils were examined with polyethylene glycol as a compatibilizer. Polyamide 6 particles were deformed into nanofibrils during drawing. For the 10% polyamide 6 case, polyethylene glycol addition reduced the polyamide 6 fibril diameter from 365.53 to 254.63 nm, owing to the smaller polyamide 6 particle size and enhanced interface adhesion. Rheological experiments revealed that the viscosity and storage modulus of the composites were increased, which was associated with the three-dimensional entangled network of polyamide 6 nanofibrils. The presence of higher aspect ratio polyamide 6 nanofibrils substantially enhanced the melt strength of the composites. The isothermal crystallization kinetics results suggested that the polyamide 6 nanofibrils and polyethylene glycol had a synergistic effect on accelerating poly(lactic acid) crystallization. With the polyethylene glycol, the crystallization half-time reduced from 103.6 to 62.2 s. Batch foaming results indicated that owing to higher cell nucleation efficiency, the existence of polyamide 6 nanofibrils led to a higher cell density and lower expansion ratio. Furthermore, the poly(lactic acid)/polyamide 6 foams exhibited a higher cell density and expansion ratio than that of the foams without polyethylene glycol.

关键词： poly(lactic acid) foaming microfibrillation rheological property crystallization

HTML PDF 收藏

Polydimethylsiloxane assisted supercritical CO

Weixia Wang, Shuai Zhou, Zhong Xin, Yaoqi Shi, Shicheng Zhao

《化学科学与工程前沿（英文）》 2016年第10卷第3期页码 396-404 doi: 10.1007/s11705-016-1577-z

摘要： Foamable high melt strength polypropylene (HMSPP) was prepared by grafting styrene (St) onto polypropylene (PP) and simultaneously introducing polydimethylsiloxane (PDMS) through?a?one-step?melt extrusion process. The effect of PDMS viscosity on the foaming behavior of HMSPP was systematically investigated using supercritical CO as the foaming agent. The results show that the addition of PDMS has little effect on the grafting reaction of St and HMSPP exhibits enhanced elastic response and obvious strain hardening effect. Though the CO solubility of HMSPP with PDMS (PDMS-HMSPP) is lower than that of HMSPP without PDMS, especially for PDMS with low viscosity, the PDMS-HMSPP foams exhibit narrow cell size distribution and high cell density. The fracture morphology of PDMS-HMSPP shows that PDMS with low viscosity disperses more easily and uniformly in HMSPP matrix, leading to form small domains during the extrusion process. These small domains act as bubble nucleation sites and thus may be responsible for the improved foaming performance of HMSPP.

关键词： high melt strength polypropylene (HMSPP) polydimethylsiloxane (PDMS) supercritical CO₂ foaming behavior